Are you ready to transform your bedroom with a stylish and functional Ottoman bed? Follow this expert installation guide to ensure a seamless setup process.

By following this expert installation guide, you can enjoy the comfort and convenience of your new Ottoman bed in no time. If you encounter any difficulties during the assembly process, refer to the provided instructions or contact customer support for assistance.

Here is a Printable and Downloadable PDF Ottoman Bed Assembly Guide

Link to a Video Installation - Video Assembly Guide

TOOLS

Tools required:

• Flathead Screwdriver
• Phillips Head Screwdriver
• Scissors
• Pliers

Optional:

• Soft Mallet

GENERAL CARE

Please take the time to carefully read through the all the guide before you commence Keep the instructions for future reference Unpack, inspect and check off all the contents Please dispose of all packing safely Small component parts could choke a child if swallowed Keep children away from the work area

Important before assembly: Read these instructions carefully before assembling or using the product. Please check the contents of the boxes before attempting to assemble this product. The instructions will have a checklist of parts and fittings. Assemble the product as close to its intended final location/room as possible.

Lay down a sheet or blanket on the floor to avoid damaging or scratching the product and protecting your floor This product is heavy so take extreme care when lifting to avoid injury or damage to the product Assemble the product as close to its intended final position in the room as possible

Wipe and clean with a slight damp soft cloth Avoid using of household cleaners and abrasives You may use dusters or Air Dusters to remove any dirt

When moving or lifting, carefully lift or have an extra person help Never drag or push the pieces as this will cause damage to the joints and could result in failure to the product that will invalidate the warranty We have tried to make the bed easy to assemble with limited assembly required.

DO NOT jump on the product or any of its parts.

DO NOT use this product if any parts are missing, damaged or worn.

DO NOT use this product unless all fixings are secured. 

If in the event that you have problems putting together or have missing or damaged pieces please contact our customer service on:

Email: sales@urbantextures.co.uk

Tel: +44 1924 471759 

Hardware Pack

1 x Headboard -  If Purchased (Example Design). 

1 x Ottoman Base (3FT) / 2 x Ottoman Base (4FT and above)

4 x Chrome Feet (3FT) / 8 x Chrome Feet (4FT and above)

3 x U-Clips (4FT and above)

4 x Headboard Bolts (If Applicable) 

4 x Headboard Spaces - Only applicable for Side Lift Ottoman Bed's

1 x Footboard - Where Applicable (Example Design)

8 x Small Screws.

4 x Footboard Clip Brackets (Should be Attached to Base and Footboard)

Base

Note: Installation of the the feet on the base is optional. As our ottoman beds come with pre-installed gas pistons, the lid can open when removing it from the packing, use one hand to hold the lids in the closed position when removing from the packing

Step 1

Remove the packing, using the pliers remove any staples that may have been attached with the packing

 

Step 2

You will find the Fitting Bag located in one of the bases.

 

Step 3

Turn the Base on it’s side and install the feet

 

Step 4

You may need a soft mallet to help push the legs into the base until they click.

 

Step 5 

Turn the base over and move both bases into position next to each other

 

Step 6

Gently open the each base, hinges and pistons come pre-installed on our beds

 

Step 7

 Use the U-Clips to join the bases and lids together

 

Step 8

 Image showing location of where U-Clips should be fixed

 

Headboard

Note: This is just for our floor standing headboards, if you have purchased a bespoke size then instructions will be provided separately

Step 1

Place the headboard against the bases, leave some space from the wall.

 

Step 2

Using the scissors make 2 cuts into the fabric to align with the holes inside each base.  

Step 3

Step 4

You can now push the bed against the wall and ready to be used

Footboard - Only if purchased or is included in the design

Note: Footboard brackets should come installed and should only require aligning and installing

Step 1

Align the footboard brackets with the base brackets

Step 2

Lift and slot the footboard onto the base

Step 3

You can now push the bed against the wall and ready to be used, ensure that the handles are easily available to lift the lid